9 Best Whirlpool Washing Machine Drain Pump (November 2026)

The best Whirlpool washing machine drain pumps include the AMI PARTS wpw10730972 W10130913 Washer Drain Pump Assembly for broad model coverage, the TOMOON W10276397 Washer Drain Pump for Whirlpool for W10276397 matches, and the ClimaTek Washing Machine Drain Pump Fits Whirlpool for W10876600 replacements.

On this page (6 sections)

1. How we chose the best Whirlpool washing machine drain pump replacements
2. Best Whirlpool drain pump options by washer model and design
3. How to match a drain pump to your Whirlpool washer
4. What symptoms point to a Whirlpool washer drain pump?
5. How to install and care for a replacement pump
6. Which Whirlpool washer drain pump should you choose?

The best Whirlpool washing machine drain pump for most compatible models is the AMI PARTS W10130913 assembly, because it covers a wide replacement-number family and selected Whirlpool, Maytag, Kenmore, and Amana washers. For a precise match, compare the pump number, washer model, mounting points, hose ports, and wiring connector.

A drain pump removes water during the drain portion of the wash cycle. A failed pump can leave water in the tub, create unusual noise, leak, or run without moving water, but a blocked filter or kinked hose can create similar symptoms.

If you want a wider starting list, see our guide to the best washer drain pump. For related brands, compare the best LG washer drain pump, best GE washer drain pump, and best Maytag washer drain pump.

Our picks at a glance

1. 1
   Best for broad model coverage

   AMI PARTS wpw10730972 W10130913 Washer Drain Pump Assembly

   9.7/10 our score

   See it on Amazon
2. 2
   Best for W10276397 matches

   TOMOON W10276397 Washer Drain Pump for Whirlpool

   9.6/10 our score

   See it on Amazon
3. 3
   Best for W10876600 replacements

   ClimaTek Washing Machine Drain Pump Fits Whirlpool

   9.5/10 our score

   See it on Amazon

4. 4

   Cylrod WPW10605427 W10425238 Washer Drain Pump Intended

   Best for Whirlpool front-load washers
   Check it
5. 5

   BlueStars W10276397 Washer Drain Pump for Whirlpool Kenmore Maytag

   Best for simple W10276397 swaps
   Check it
6. 6

   Beaquicy W10409079 Washer Drain Pump Fit

   Best for included mounting hardware
   Check it
7. 7

   REEPLAR 280187 8181684 Front Load Clothes Washer

   Best for sealed front-load assemblies
   Check it
8. 8

   3363394 Washer Drain Pump by Seentech -Compatible

   Best for direct-drive washers
   Check it
9. 9

   Blutoget 2026 UPGRADED W10536347 W10155921 W10049390 Washer

   Best for W10536347 replacements
   Check it

How we chose the best Whirlpool washing machine drain pump replacements

The best Whirlpool washing machine drain pump depends on fit more than brand name. We compared replacement numbers, stated washer families, voltage, flow rate, pump layout, mounting hardware, and the type of washer each pump targets.

That comparison matters because two pumps can look alike and still connect in different ways. A different hose port, screw pattern, or wiring connector can turn a simple swap into a return.

Our score weighs specs, features, and buyer feedback against what you are shopping for. It does not replace a model check, and it should not be read as a guarantee for your exact machine.

Fit comes first in every case. The old pump number, the full washer model, and the physical connection points tell you more than a general claim about Whirlpool compatibility.

For front-load machines, a pump with the correct filter or housing layout may be more useful than a general replacement. The filter position and inlet and outlet arrangement are part of the design, not small details to ignore.

For older direct-drive machines, the motor connection and two-port arrangement matter more than a broad brand list. Those washers use a different pump path from many newer designs.

Voltage and flow rate also help narrow the field. They are useful checks, but they sit behind part number and mounting layout when you make the final match.

We also looked at what is included in the package. Screws, clamps, or an elbow can save a second trip, while a pump only package may be fine if your old hardware is still usable.

Care guidance was part of the review as well. A correct pump can still struggle if the filter stays clogged or the drain hose is kinked, so setup and upkeep belong in the decision.

Use the ranking as a shortlist, then do the exact match.

Best Whirlpool drain pump options by washer model and design

The top picks separate into several fit groups: W10130913 and WPW10730972 assemblies, W10276397 pumps, front-load assemblies, and older direct-drive designs. Start with the number printed on the old pump, then confirm it against the washer model.

AMI PARTS wpw10730972 W10130913 Washer Drain Pump Assembly: Best for broad model coverage

1

AMI PARTS wpw10730972 W10130913 Washer Drain Pump Assembly: Best for broad model coverage

9.7/10Our score

• 120V, 60Hz, 1.2A, 78W
• Replaces multiple W10130913 and WPW10730972 numbers
• Fits selected Whirlpool, Maytag, Kenmore, and Amana washers

A wide replacement-number list makes this a strong first match when your old pump carries W10130913 or WPW10730972. It also covers selected Whirlpool, Maytag, Kenmore, and Amana models.

See it on Amazon

Pros

• Broad replacement-number coverage
• 120V, 60Hz, 1.2A, 78W specifications
• Model references include several WFW series washers

Cons

• Exact model fit still needs checking
• The package contains one assembly

The AMI PARTS assembly is the strongest general pick in this group because its replacement list includes WPW10730972, W10130913, PS11757304, AP6023956, and several other numbers. It is stated for selected Whirlpool, Maytag, Kenmore, and Amana washers.

Its electrical specification is 120V, 60Hz, 1.2A, and 78W. The assembly is plastic, measures 8.6 x 5.5 x 5.5 in, and includes one pump assembly.

The model references include WFW9700, WFW9550, WFW94HEAW0, WFW9250, WFW9200, WFW9150, WFW9050, WFW8500S, WFW8410, WFW8400, and WFW8300 families. Treat those references as a starting point and match the complete model number before ordering.

This pick suits a repair where the pump number already matches W10130913 or WPW10730972. It is less suitable as a guess based only on the Whirlpool name.

The broad number list is the main benefit here. It helps when the old part carries one of several equivalent numbers that all point to the same pump family.

Daily use still depends on a clean drain path. A filter full of coins, hair, or lint can strain any new pump, so clear that area during the repair.

Set up matters too, since hose position and clamp tightness affect leaks after the swap. Photograph the old connections before you loosen them and check each joint after the first test cycle.

TOMOON W10276397 Washer Drain Pump for Whirlpool: Best for W10276397 matches

2

TOMOON W10276397 Washer Drain Pump for Whirlpool: Best for W10276397 matches

9.6/10Our score

• 120V, 60Hz, 85W, 0.95A
• Replaces WPW10276397VP and related numbers
• Fits selected Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, Roper, and Admiral models

This is a focused choice for washers using the W10276397 or B40-3A family. The non-removable impeller makes regular washer-filter cleaning especially useful.

See it on Amazon

Pros

• Clear W10276397 replacement family
• 85W and 0.95A specifications
• Drain-hose maintenance guidance

Cons

• Compatibility depends on the exact washer model
• One pump is included

TOMOON targets the W10276397 family, also called B40-3A, LP397, AP6018417, and related replacement numbers. It is stated for selected Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, Roper, and Admiral washers.

The pump uses 120V, 60Hz, 85W, and 0.95A specifications, with an acrylonitrile butadiene styrene body. One pump is included.

The non-removable impeller means lint, hair, and fabric scraps can collect inside the pump chamber. Regularly clean the washer filter, especially after towels, bedding, or pet-hair loads.

The drain hose also affects noise and drainage. Keep it at the required height, avoid kinks, and secure it so water does not flow back toward the washer.

This option suits a washer that already uses the W10276397 number and has the same mounting and hose layout. It is a poor choice if your old pump belongs to a different family, even if the brand name matches.

Care is simple but not optional with a sealed impeller design. Keep the washer filter clean so debris has less chance to build up inside the pump over time.

During setup, check the hose route as part of the repair. A flat or kinked hose can cause noise and poor draining that look like a pump fault.

ClimaTek Washing Machine Drain Pump Fits Whirlpool Maytag Kenmore: Best for W10876600 replacements

3

ClimaTek Washing Machine Drain Pump Fits Whirlpool: Best for W10876600 replacements

9.5/10Our score

• Replaces W10876600, W10727777, B25-3A04, AP6004933, and related numbers
• Designed for selected Whirlpool, Maytag, Amana, Kenmore, and Sears units
• One drain pump

Choose this when your old pump matches the W10876600 or W10727777 family. Its value is the direct replacement-number match rather than electrical detail.

See it on Amazon

Pros

• Useful replacement-number coverage
• Fits several related brands
• One direct replacement part

Cons

• Electrical specifications are not stated here
• Exact model verification remains necessary

ClimaTek is a focused choice for the W10876600 and W10727777 replacement family. It also replaces B25-3A04, AP6004933, 4455877, W1087600VP, and PS11738156.

The pump is designed for selected Whirlpool, Maytag, Amana, Kenmore, and Sears units. It is a black, single-item drain pump, but electrical specifications are not stated in the supplied product information.

That makes the replacement number and washer model especially important. Compare the old pump's connector and hose positions before you remove anything.

Choose ClimaTek when your existing pump carries one of the matching numbers. If your washer uses W10130913, W10276397, or W10409079, use the corresponding option instead.

The trade-off here is clear. You get a direct match for a specific family, but you get less electrical detail to compare against the old part.

That means the physical checks carry more weight. Look at the connector shape, port positions, and screw points while the old pump is still in place.

For care, keep the filter and hose clear as you would with any drain pump. A correct part will still underperform if debris restricts the drain path.

Cylrod WPW10605427 W10425238 Washer Drain Pump Intended: Best for Whirlpool front-load washers

4

Cylrod WPW10605427 W10425238 Washer Drain Pump Intended: Best for Whirlpool front-load washers

9.4/10Our score

• Fits selected Whirlpool and Maytag front-load washers
• 20 liters per minute flow rate
• ABS shell and rubber sealing gasket

This pump targets selected Whirlpool Duet and Maytag front-load models using WPW10605427 or W10425238. The model list is the key buying check.

See it on Amazon

Pros

• Front-load model focus
• 20 liters per minute flow rate
• Rubber gasket for the pump seal

Cons

• Not a general fit for every Whirlpool washer
• The listed size is 7.3 x 3.5 x 8.2 in

Cylrod is intended for selected Whirlpool and Maytag front-load washers, including Whirlpool WFW75HEFW0, WFW72HEDW0, WFW92HEFW0, WFW8540FW1, WFW92HEFC0, WFW8740DW0, WFW7590FW0, and related models.

It replaces WPW10605427, W10605427, WPW10425238, W10799064, W10799065, W10903216, AP6023357, PS11756700, PS11754613, and W10918044. The pump is rated at 120V and has a stated flow rate of 20 liters per minute.

Its ABS shell and rubber sealing gasket are useful details for a front-load repair where the housing and seal must match. The listed size is 7.3 x 3.5 x 8.2 in.

Use the complete model number, not just “Whirlpool Duet,” because several front-load pump designs exist.

This pick suits front-load washers in that stated model group. It does not suit every Whirlpool washer, and top-load machines should not be treated as an automatic match.

The flow rate gives a sense of how the pump handles water during a drain cycle. It still needs the right housing fit and seal placement to work as intended.

For setup, disconnect power before you remove the back panel and locate the pump below the drum. Keep the gasket seated evenly, since a small seal error can lead to a leak under pressure.

BlueStars W10276397 Washer Drain Pump for Whirlpool Kenmore Maytag: Best for simple W10276397 swaps

5

BlueStars W10276397 Washer Drain Pump for Whirlpool Kenmore Maytag: Best for simple W10276397 swaps

9.3/10Our score

• 120V, 60Hz, 85W, 0.95A
• Measures 5.8 x 6.1 in
• Replaces W10276397, B40-3A, LP397, and related numbers

BlueStars is another W10276397 option for selected Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, Roper, and Admiral washers. Compare the old pump number before choosing between this and TOMOON.

See it on Amazon

Pros

• Clear electrical specifications
• Known W10276397 replacement family
• One pump included

Cons

• Exact fit depends on the washer model
• The data includes an inconsistent voltage field, so verify the model and wiring

BlueStars is another W10276397 option for selected Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, Roper, and Admiral washers. It replaces AP6018417, WPW10276397, WPW10276397VP, PS11751719, 1874334, B40-3A, and LP397.

The stated electrical details are 120V, 60Hz, 85W, and 0.95A, with dimensions of 5.8 x 6.1 in. One W10276397 drain pump is included.

Compare this pick with TOMOON by checking the old pump's number, connector, and mounting arrangement. Shared replacement numbers can still require exact model verification.

The product data includes an inconsistent voltage field elsewhere, so use the washer model and physical wiring as final checks before installation.

This option suits a straightforward W10276397 swap in a matching washer. It is best when the old pump and the replacement share the same ports and mounting points.

The main trade-off is that two brands cover the same part family. That choice should turn on layout and model fit rather than a general preference for one name.

For care, keep the filter clean and the drain hose free of kinks. Those habits help prevent slow draining after the new pump is fitted.

Beaquicy W10409079 Washer Drain Pump Fit: Best for included mounting hardware

6

Beaquicy W10409079 Washer Drain Pump Fit: Best for included mounting hardware

9.2/10Our score

• 120V, 0.95A, 60Hz
• Includes one pump and 3 screws
• Rubber elbow and clamp mechanisms

This option suits selected Whirlpool, Maytag, and Kenmore washers using W10409079 or W10403802. The included screws, elbow, and clamps can simplify a replacement when those connection points match.

See it on Amazon

Pros

• 45 liters per minute flow rate
• Three screws included
• Rubber elbow and clamps

Cons

• Only selected washer models fit
• The pump size is about 7.9 x 6.5 x 3.9 in

Beaquicy fits selected Whirlpool, Maytag, and Kenmore washers using W10409079, W10403802, WPW10409079, AP6021043, PS11754363, EAP11754363, or 2118648.

The package includes one pump and 3 screws, plus a rubber elbow and clamp mechanisms. The pump uses 120V, 0.95A, and 60Hz specifications and has a stated flow rate of 45 liters per minute.

The black orifice measures 1.32 in and the white orifice measures 1.26 in. The listed pump size is about 7.9 x 6.5 x 3.9 in.

This option suits a repair where the hose connection and screw layout match. Disconnect power and water before removing the old pump, and photograph the hose positions first.

The included hardware is a real benefit when the old screws or clamps are worn. It can make the job simpler, but only if the sizes match your washer.

The rubber elbow and clamps also matter for sealing. Fit them carefully and tighten them evenly so the joints stay firm without damaging the hose.

For daily use, watch the first few drain cycles for drips at each connection. A short check after installation can catch a loose clamp before it becomes a floor leak.

REEPLAR 280187 8181684 Front Load Clothes Washer: Best for sealed front-load assemblies

7

REEPLAR 280187 8181684 Front Load Clothes Washer: Best for sealed front-load assemblies

9.1/10Our score

• Complete assembly with motor, filter, and plastic housing
• 120V, 60Hz, 0.95A
• Fits selected Whirlpool, Maytag, and Kenmore front-load washers

REEPLAR is aimed at selected older front-load Whirlpool, Maytag, and Kenmore families. Its complete assembly includes the motor, filter, and inlet and outlet housing.

See it on Amazon

Pros

• Complete pump assembly
• Built-in filter
• Broad model references for selected front-load washers

Cons

• Compatibility must be checked against the exact model
• The stated power fields conflict, so use the model and connector as the final checks

REEPLAR is a complete assembly with a motor, filter, inlet housing, and outlet housing. It targets selected Whirlpool, Maytag, and Kenmore front-load washers using 280187, 8181684, AP3953640, PS1485610, EAP1485610, and related numbers.

The assembly is rated at 120V, 60Hz, and 0.95A in its product information. It is a grey plastic unit, and one pump body is included.

The model references cover families such as WFW9200S, WFW9300V, WFW9400S, WFW9400V, WFW9410XW00, WFW9451XW00, WFW9470WL00, WFW9500T, and selected Maytag and Kenmore washers.

Choose it when the old assembly has the same filter and housing design. Do not substitute it solely because both machines are front-load washers.

A complete assembly can suit a repair where the filter and housing need replacement as a set. That is different from a motor-only swap, so compare the whole unit before you order.

The trade-off is that fit has to be exact across more parts. Filter placement, housing shape, and connections all need to line up with the old assembly.

For care, clean the built-in filter on the schedule for your washer. A blocked filter can raise noise and slow drainage even when the motor is new.

3363394 Washer Drain Pump by Seentech: Best for direct-drive washers

8

3363394 Washer Drain Pump by Seentech -Compatible: Best for direct-drive washers

9.0/10Our score

• Direct-drive pump without a belt
• Two water ports
• Fits selected Whirlpool, Kenmore, Roper, Estate, Crosley, and Inglis models

This is the right type to investigate for a direct-drive washer that uses the 3363394 family. The two water ports and direct motor connection must match the old pump.

See it on Amazon

Pros

• Direct-drive design
• Two-port layout is clearly stated
• Fits several older brand families

Cons

• Not intended for every Whirlpool washer
• Exact model matching is essential

Seentech targets older direct-drive Whirlpool washer designs using 3363394, WP3363394VP, AP6008107, 21024, 3348015, 3352492, 62516, 64076, 8235, and related numbers.

The pump removes water without a belt and connects directly to the motor. It has one large water port and one small water port, so those openings must match the old pump and hose layout.

It is stated for selected Whirlpool, Kenmore, Roper, Estate, Crosley, and Inglis models. The pump uses copper, steel, and plastic materials and includes one 3363394 drain pump.

This is a different design path from many newer front-load pumps. Confirm that your washer is a compatible direct-drive model before choosing it.

This pick suits older direct-drive machines in the stated families. It is not a general Whirlpool pump, and the two-port layout is a key part of the match.

Daily use depends on keeping both ports clear and the hoses seated well. A blockage in either path can leave water in the tub or cause a leak at the joint.

For setup, note which hose goes to the large port and which goes to the small port before removal. That simple record prevents a cross connection during reassembly.

Blutoget 2026 UPGRADED W10536347 W10155921 W10049390 Washer: Best for W10536347 replacements

9

Blutoget 2026 UPGRADED W10536347 W10155921 W10049390 Washer: Best for W10536347 replacements

8.6/10Our score

• 110V, 50/60Hz, 85W
• Includes one pump and 3 mounting screws
• Fits selected Whirlpool, Kenmore, and Maytag washers

Blutoget targets selected Whirlpool, Kenmore, and Maytag washers using W10536347, W10155921, or W10049390. The included mounting screws help when the old pump uses that three-screw layout.

See it on Amazon

Pros

• Three mounting screws included
• 16 ft maximum lifting height
• Detailed replacement-number family

Cons

• Lower score because fit is more model-specific
• The product data lists four packs while the package description says one pump

Blutoget targets selected Whirlpool, Kenmore, and Maytag washers using W10536347, W10155921, W10049390, W10217134, W10238317, W10281682, AP5650269, PS5136124, and EAP5136124.

The package description includes one pump and 3 mounting screws. The stated specifications are 110V, 50/60Hz, and 85W, with a maximum lifting height of 16 ft.

The product information describes a strong ABS and metal construction, a shield cover, and a metal clip at the bend. The listed size is 6.5 x 3.94 x 8.3 in.

Use this pick when the old pump has the same number and three-screw mounting pattern. The product data lists four packs in one field while the package description says one pump, so confirm the package details before ordering.

This option suits a W10536347 family repair where the screws and hose bend match. It is less suited to a washer that uses a different mounting pattern.

The stated lifting height is useful context for where the hose must reach. It does not remove the need to check port size and connector fit.

For care, secure the metal clip and keep the hose route smooth. A firm connection at the bend helps prevent the hose from working loose during a drain cycle.

How to match a drain pump to your Whirlpool washer

The safest match uses four checks: the full washer model, the old pump number, the mounting arrangement, and the wiring connector. Brand-only matching is not enough because Whirlpool washer families use different pump bodies and replacement numbers.

Start by photographing the old pump before disconnecting it. Record every number printed on the motor or housing, then compare the hose ports and screw positions with the replacement.

For a pump with a wiring connector, count the terminals and compare their shape. A pump with the right number but a different connector may not be a direct swap.

Also check whether your machine is top-load, front-load, or direct-drive. The Cylrod and REEPLAR options target front-load families, while Seentech focuses on direct-drive designs.

If you need a related hose after confirming the pump, see the guide to the best LG washer drain hose. Hose height, kinks, and backflow can affect drainage symptoms even when the pump is working.

What symptoms point to a Whirlpool washer drain pump?

A Whirlpool washer drain pump may need attention when the machine will not drain, drains slowly, leaks near the pump, makes unusual noise, or leaves clothes wetter than usual. Some models also display a drain-related error code.

Those symptoms can point to the pump, but they can also point to a blockage elsewhere. Treat them as a reason to inspect, not as proof that the pump has failed.

Check the easy causes first. Unplug the washer, inspect the drain hose for kinks, and clean the accessible filter or trap according to the washer instructions.

The drain hose is a common culprit because a bend or partial blockage can slow water flow. Straighten the hose and check that it is secured at the correct height before you move on.

A pump that hums but does not move water may have a blocked impeller or a failed motor. Do not reach into the pump while the washer is connected to power.

Noise needs a careful listen. A rattle can come from a coin in the filter, while a steady hum can mean the motor is turning without effective pumping.

Leaking near the pump deserves a close look at the hose joints and seals. Water may travel along a hose before it drips, so the visible drip point is not always the failed joint.

Slow draining can also be tied to debris from towels, bedding, or pet hair. Those loads send more lint and hair toward the filter and pump than a normal mixed load.

If the washer will not start a drain at all, check power and the basic controls. An error code should be read with the manual for your exact model, since codes can vary by family.

For a broader explanation of the water-removal stage, read How a Washer Spin Cycle Extracts Water from Your Clothes. The spin cycle and drain pump work together, but they are separate parts of the process.

Keep the inspection order simple and safe. Start with the hose and filter, then move to the pump only after power is disconnected and standing water is removed.

How to install and care for a replacement pump

Disconnect the washer from power and shut off its water supply before opening the cabinet. Remove standing water with a suitable container, wear work gloves, and keep towels nearby for water left in the hoses.

Photograph the old pump, hose clamps, screw positions, and wire connector. Replace one connection at a time when possible, and make sure every clamp is tight without damaging the hose.

After installation, run a short rinse or drain cycle while watching for leaks. Listen for unusual noise and confirm that water leaves through the drain hose.

Clean the filter at the interval recommended for your washer. Loads containing towels, bedding, lint, or pet hair can send more debris toward the pump.

High-efficiency washers can use different water levels and cycle behavior. Our guide to [What Makes a Washer High Efficiency?

HE Basics Explained](/what-makes-a-washing-machine-high-efficiency/) explains why the machine may not behave like an older washer during draining.

Which Whirlpool washer drain pump should you choose?

Choose AMI PARTS when your old pump matches W10130913 or WPW10730972 and you want the broadest stated replacement-number coverage. Choose TOMOON or BlueStars when your pump matches W10276397, and compare their physical layout before deciding.

Choose Cylrod or REEPLAR for the matching front-load families. Choose Seentech for a compatible 3363394 direct-drive washer, Beaquicy for a W10409079 match with screws and hose hardware, and Blutoget for the W10536347 family with a three-screw layout.

The final decision rule is simple: match the full washer model, pump number, mounting points, hose ports, and connector before ordering. If the washer is in an RV or another compact installation, compare the best portable washing machines for RVs before attempting a pump repair on a machine that may not use a Whirlpool-compatible design.

Start with the number printed on the old pump and the full model number from the washer label. Those two checks will rule out most wrong options before you compare price or package contents.

Then compare the physical details that do not show up in a brand name. Hose port size, screw pattern, filter position, and wiring shape all need to match the part you remove.

Consider what is in the box as a secondary factor. Included screws, clamps, or a complete housing can help, but they cannot fix a pump that does not fit your model.

Think about care after the repair as well. A new pump will last better if you clean the filter, avoid hose kinks, and watch for early leaks during the first test cycle.

If the old pump number is unreadable, use the washer model and a photo of the pump layout to narrow the field.

For a front-load washer, pay extra attention to the filter and housing design. For a direct-drive top-load washer, pay extra attention to the motor connection and port arrangement.

That approach keeps the choice grounded in the machine you own.

Our top 3 picks at a glance

1. 1
   Best for broad model coverage

   AMI PARTS wpw10730972 W10130913 Washer Drain Pump Assembly

   9.7/10 our score

   See it on Amazon
2. 2
   Best for W10276397 matches

   TOMOON W10276397 Washer Drain Pump for Whirlpool

   9.6/10 our score

   See it on Amazon
3. 3
   Best for W10876600 replacements

   ClimaTek Washing Machine Drain Pump Fits Whirlpool

   9.5/10 our score

   See it on Amazon

Frequently asked questions

How do I choose a Whirlpool washing machine drain pump?

Match the old pump's part number and the washer's full model number first. Then compare the mounting points, hose ports, electrical connector, voltage, and included hardware.

A pump that fits another Whirlpool family may still be wrong for your washer.

What causes a Whirlpool washer drain pump to fail?

Common symptoms include slow or incomplete draining, unusual pump noise, leaking, an error code, or a motor that runs without moving water. Check the drain hose and filter for blockage before replacing the pump, because a clog can look like pump failure.

Can I install a Whirlpool washer drain pump myself?

Many replacement pumps use basic hand tools, but the access route varies by washer. Disconnect power and water, remove standing water, wear gloves, photograph hose and wire positions, and use the washer's service instructions before removing the old pump.

Are Whirlpool washer drain pumps interchangeable?

No. Some pumps share replacement numbers across Whirlpool, Maytag, Kenmore, and Amana models, but mounting points, ports, wiring, and model-year design can differ.

Use the full washer model and the old pump number rather than choosing by brand alone.